About HP ProCurve
HP ProCurve was the name of the networking division of Hewlett-Packard from 1998 to 2010 and associated with the products that it sold. The name of the division was changed to HP Networking (also called HP ProCurve Networking) in September 2010 after HP bought 3Com Corporation. As the then-ProCurve division began to offer LAN switches, Core, Datacentre, Distribution, Edge, Web managed and Unmanaged Switches. The ProCurve was also used with Network Management, Routing and Security products. HP ProCurve transceivers as the part of its networking accessories that are applied to their corresponding switches or routers. Today, we will introduce some knowledge of the HP GBICs and SFPs.
Products Involved In This Paper
HP ProCurve Gigabit-SX-LC Mini-GBIC (Product No. J4858A/J4858B/J4858C)
A small form-factor pluggable (SFP) Gigabit SX transceiver with LC port that provides a full-duplex Gigabit solution up to 550 m on multimode fibre.
FS.COM:
- NEW HP J4858A X121 Compatible 1000BASE-SX SFP 850nm 550m Transceiver Module
- NEW HP J4858B X121 Compatible 1000BASE-SX SFP 850nm 550m Transceiver Module
- NEW HP J4858C X121 Compatible 1000BASE-SX SFP 850nm 550m Transceiver Module
HP ProCurve Gigabit-LX-LC Mini-GBIC (Product No. J4859A/J4859B/J4859C)
An SFP format gigabit transceiver with LC connectors using LX technology.
FS.COM:
- NEW HP J4859A Compatible 1000BASE-LX SFP 1310nm 10km Transceiver Module
- NEW HP J4859B Compatible 1000BASE-LX SFP 1310nm 10km Transceiver Module
- NEW HP J4859C Compatible 1000BASE-LX SFP 1310nm 10km Transceiver Module
HP ProCurve Gigabit-LH-LC Mini-GBIC (Product No. J4860A/J4860B/J4860C)
A small form-factor pluggable (SFP) Gigabit LH transceiver that provides a full-duplex Gigabit solution up to 70 km on single-mode fibre.
FS.COM:
- NEW HP J4860A Compatible 1000BASE-ZX SFP 1550nm 80km Transceiver Module
- NEW HP J4860B Compatible 1000BASE-ZX SFP 1550nm 80km Transceiver Module
- NEW HP J4860C Compatible 1000BASE-ZX SFP 1550nm 80km Transceiver Module
Knowledge You Should Know About HP GBICs and SFPs
For the above products, there usually are many questions about them. The following infomation will make you to know more about them.
Supported Platform
According to HP ProCurve Networking Mini-GBIC Support Matrix, we can easily find out which HP GBICs and SFPs are supported on which ProCurve Systems. General rules are:
- Please use only genuine or high-quality 100% compatible ProCurve Mini-GBICs and SFPs on ProCurve System.
- Newer ProCurve products require revision “B” or later Mini-GBICs and SFPs (product number ends with the letter “B” or later, for example J4858B, J4859C).
About the Version A, B, C
HP GBICs and SFPs have three version, but you may not find A and B anymore in HP’s official website. In fact, the version A, B and C are the development of HP ProCurve Mini-GBIC and SFP. Though there is no big difference between these three version, some improvement will be added in the newest version, and the supported platforms adjustment. The “revision C” Mini-GBICs (eg. J4858C, J4859C, J4860C) are supported in all ProCurve products that support Mini-GBICs. In addition, “revision B” and “revision C” mini-GBICs can be used together in any ProCurve switch that supports mini-GBICs. Actually, as the transitional products, HP stops offering the version A and version B. But version C are not supported on some old switches, thus, some users have still used the version A or version B. FS.COM can support the 100% compatible HP ProCurve Mini-GBICs and SFPs at version A, B and C, such as J4858A/B/C, J4859A/B/C, J4860A/B/C.
Mini-GBICs and SFPs hot-swappable
All ProCurve Mini-GBICs and SFPs are hot-swappable (they can be installed and removed while the switch is powered on). However, the network cable should be disconnected before removing the HP GBICs or SFPs from the switch.
Best practice tip: After inserting a transceiver into a ProCurve switch, the Mode LED will come on for two seconds while the transceiver is initialized. Do not remove the transceiver until the Mode LED has turned off. For the Switch 2600 and 2800 Series: After inserting a transceiver into a 2600 or 2800 switch, the “M” LED will come on to indicate that the mini-GBIC slot is active. Wait at least two seconds after the “M” LED comes on if you need to remove the transceiver.
Conclusion
FS.COM is a professional manufacturer and supplier of optical networking solutions. We can supply 100% compatible fibre optic transceiver of many brands, like HP, Cisco, Dell, D-link etc. with a incredible discount. About HP, you can find a full product line of our New HP transceivers with a good price and enjoy same-day shipping. In addition, according to your requirements, we welcome any inquiry for customized fibre optical transceiver. FS.COM’s aim is offering the best quality products and perfect solutions, saving customers’s time and money, making customers enjoy personalisation.
Related Article: