Category Archives: Fiber Optic Network

fiber equipment is specialized in manufacturing fiber optic cables and relative fiber optic …We work with domestic telecom companies to build fiber optic network.

How to Save Cost for 500Gbps Metro Network Over Long Distance?

Increasing bandwidth has always been the most important task of telecom engineers. Through decades of research and engineering effort, 40Gbps and 100Gbps solutions have been used for network applications. But 40G and 100G transceivers can’t support too much long distance (QSFP-40G-ER4 for 40 km, QSFP-100G-LR4 for 10 km). How to extend the 500Gbps link to thousands of kilometers in Metro network within limited budget?

Save Fiber Cost–500Gbps Over Single Fiber Cable

Fiber cable cost takes a certain percentage in the whole network budget. Point to point connection needs many cables, while WDM technology take well care of this issue. In a metro network, usually multiple 10Gbps signals are transmitted by the use of DWDM Mux/Demux over a single fiber cable, which can save lots of money on multiple fiber cables and cable management issues. Then how to save cost to transmit 500Gbps signals over single fiber cable?

It sounds unbelievable. But we have the cost-effective solution. As we know, it will cost too much to replace all the current network system for upgrading to higher data rate. To save cost for increasing bandwidth, some producers add an extra port on DWDM Mux/Demux and that is 1310nm or 1550nm port. This port supports 1310nm or 1550nm transceiver. With such port, you can add 1G/10G/40G/100G to the existing DWDM network. For instance, we use 40-channel C21-C60 dual fiber DWDM Mux/Demux with 1310nm port and 1310nm band port for 1G/10G/40G/100G “grey” light. Plug 10G DWDM SFP+ transceivers into 40 channels, the overload is 400Gbps. Once plugging a 1310 40G QSFP+ LR4/ER4, then the total link reach up to 440G (400G + 40G). If install a 100G QSFP28 LR4 transceiver into 1310 port, the whole transport will be 500Gbps (400G + 100G). See this solution realize the goal of saving cost to run such huge network load over a single fiber.

500g dwdm network

40ch dwdm mux-demux

Extend 500G Transmission Distance

Since 500G signals can be transmitted over a single fiber cable, we have another issue to be solved. 500G transmission distance is needed far more than few kilometers in real life, maybe thousand of kilometers. How to extend the transmission distance?

According to IEEE standard, LR4 and ER4 transceivers can support the reach of 10 km and 40 km in the in ideal conditions, not considering fiber loss or connector loss. To extend 500Gpbs transmission distance, we need SOA (Semiconductor Optical Amplifier) and EDFA (Erbium Doped Fiber Amplifier). Add an SOA to support 40G/100GBASE-LR4 transceiver (over 1310 nm). The SOA is used to amplify incoming (Rx) signal on the receiving side of the link. So that the distances can reach up to 60 km. In 10Gbps DWDM networks, the signal transmission distance can be extended to hundreds of kilometers by the use of and EDFA (Erbium Doped Fiber Amplifier).

500g dwdm network-1

Recommended DWDM Solutions for 500Gbps Metro Network
ID# FS Part Number Description
35887 40MDD-1RU-A1-FSDWDM 40 Ch 1RU Duplex DWDM MUX DEMUX C21 to C60 with 1310nm Port and Monitor Port
14491 DWDM-SFP10G-40 10GBASE 100GHz DWDM SFP+ 40km, LC Duplex Interface, C21 to C60
31533 DWDM-SFP10G-80 10GBASE 100GHz DWDM SFP+ 80km, LC Duplex Interface, C21 to C60
14599 DWDM-XFP10G-40 10GBASE 100GHz DWDM XFP 40km, LC Duplex Interface, C21 to C60
14650 DWDM-XFP10G-80 10GBASE 100GHz DWDM XFP 80km, LC Duplex Interface, C21 to C60
35208 QSFP-LR4-40G 40G QSFP+ LR4 1310nm 10km, LC Duplex Interface
35210 QSFP-ER4-40G 40G QSFP+ ER4 1310nm 40km, LC Duplex Interface
35014 CFP2-LR4-100G 100G CFP2 LR4 1310nm 10km, LC Duplex Interface
35192 FS-SOA-G10 10dB Gain 1310nm Semiconductor Optical Amplifier
31366 EDFA-BAO22 20dBm Output C-band 40 Channels 26dB Gain Booster EDFA

Summary

DWDM technology is very necessary to extend Metro Network reach. In this 500Gpbs Metro network, I have introduced very detailed cost-effective solutions. Remember all the indispensable DWDM equipment such as DWDM transceivers, DWDM Mux/Demux, EDFA, etc. For more information, please visit the site about FS.COM Long Haul DWDM Network Solution.

Related articles:

How to Extend 40G Connection up to 80 km?
Economically Increase Network Capacity With CWDM Mux/DeMux

How to Understand Tx Power vs. Rx Power of a Fiber Transceiver?

As we all know, single mode fiber optic transceiver is designed for long distance data transmission and multimode fiber optic transceiver is for short distance link. How to calculate the specific distance that a fiber optic transceiver can support at a certain occasion? What factors are crucial to the transmission distance? Do you have any idea of Tx (transmit) power and Rx (receive) power level of a fiber optic transceiver? This article will show you by introducing 10GBASE-SR SFP+ and 10GBASE-LR SFP module.

Tx Power and Rx Power of a Fiber Transceiver

First, let’s understand the most two important factors of the fiber optic transceiver: Tx power and Rx power. The optical Tx power is the signal level leaving that device and it should be within the transmitter power range. The Rx power is the incoming signal level being received from the far end device and it should fall within the receive power range.

10GBASE-SR SFP+ is a multimode fiber transceiver and can support the distance of 300 m over OM3 multimode fiber patch cable. While 10GBASE-LR SFP module is a single mode type and can run the network distance up to 10 km over single mode fiber patch cords. Before purchasing 10GBASE SFP+ module, you must carefully read the product details. The following lists the product details about 10GBASE-SR SFP+ and 10GBASE-LR SFP module from Fiberstore. As showing below, Tx power of this Cisco compatible 10GBASE-SR SFP+ is between -7.3 dBm and -1 dBm. The maximum receive power is below -11.1 dBm. With regard to Cisco compatible 10GBASE-LR SFP module, Tx power is from -8.2 to 0.5 dBm and the maximum Rx power is -14.4 dBm.

Tx Power and Rx Power of 10GBASE-SR SFP+

Tx Power and Rx Power of 10GBASE-SR

Tx Power and Rx Power of 10GBASE-LR SFP+ Module
Tx Power and Rx Power of 10GBASE-LR
Tx Power and Rx Power VS. Optical Power Budget

To calculate the specific distance of a fiber optic transceiver, we need to know its optical power budget (maximum allowable loss).

Optical power budget = Tx power – Rx power

Therefore, according to the Tx power and Rx power, we can calculate the maximum allowable loss of 10GBASE-SR SFP+ and 10GBASE-LR SFP module.

Optical Power Budget of 10GBASE-SR SFP+

Min Tx Power = -7.3 dBm
Max Rx Power = -11.1 dBm
Optical power budget (maximum allowable loss) = (-7.3 dBm) – (-11.1 dBm)=3.4 dBm

Optical Power Budget of 10GBASE-LR SFP+ Module

Min Tx Power = -8.2dBm
Max Rx Power = -14.4 dBm
Optical power budget (maximum allowable loss) = (-8.2 dBm) – (-14.4 dBm)=6.2 dBm

Tx Power and Rx Power VS. Transmission Distance

Except optical power budget, we have to consider other factors including the link length, fiber optical connectivity components, fusion splicing points and some unpredictable fiber attenuation caused by fiber patch cable bending (usually the attenuation is about 3 dB). The loss of each connector is 0.6 dB and 0.1 dB of each fusion splicing point. Suppose we use 10GBASE-LR SFP+ module to build a network covering 2 connectors, 4 fusion splicing points. This module is interfaced with LC single mode fiber patch cord. If the single mode fiber cable has the wavelength of 1310 nm, the cable loss is about 0.35 dB per kilometer.

The worst optical loss = Power Budget – Total Optical Power Loss=6.2 dB – 1.2dB (2×0.6 dB) – 0.4dB (0.1×4) – 3dB (safety factor) = 1.6 dB
Worst case distance = {Worst case OPB, in dB} / [Cable Loss, in dB/km]=1.6dB/0.35dB/km
So we can get 10GBASE-LR SFP+ module can support at least 4.57 km at this occasion. Data transmission distance is mainly influenced by the optical power budget and fiber cable loss. From the above content, the optical power budget of 10GBASE-SR SFP+ is smaller than that of 10GBASE-LR SFP+ module. The more the optical power budget, the further the fiber transceiver can support. What’s more, the cable loss of multimode fiber cable is larger than that of single mode fiber cable. Obviously 10GBASE-LR SFP+ module can support longer link distance than 10GBASE-SR SFP+.

network building

Note: The optical power budget is based on a theoretical calculation, and is just for reference. The transmission distance should be calculated based on the power budget of fiber transceiver module tested on the switch and some practical attenuation.

Conclusion

Tx power and Rx power level of a transceiver are the main factors of transmission distance. The more the optical power budget, the better the transceiver. Before purchasing a transceiver, you’d better calculate the optical power budget according to transceiver module details.

Selection Guide on PoE Switch

Currently IP cameras are widely used for video surveillance due to the high requirements for security. Typically, the IP cameras are with PoE functions, then PoE switch is needed for the connection. But some users feel confused about the PoE switch and don’t know how to choose a suitable PoE switch. This article is going to introduce you some guides on PoE switch selection.

What Is PoE and PoE Switch?

PoE is short for power over Ethernet. With PoE technology, data and power can be transmitted over a single Cat5e cable. A PoE switch is a device that contains multiple Ethernet ports to provide power and network communications to IP cameras. PoE switch is an economical and reliable solution for small business networks to deploy wireless access points and IP surveillance cameras.

Fiberstore poe switch

Considerations for PoE Switch Selection
Numbers of Ports

The most important is to check whether the numbers of ports on PoE switch are enough to connect all your devices. Fiberstore offers PoE switches including 8 ports, 24 ports, and 48 ports. PoE ports are flexible to connect with Cat5e cable without additional settings. All of our PoE switches have 2 Gigabit uplink SFP ports or 4 SFP+ ports. Uplink ports allow long distance data transmission between switches. With these ports, you can easily expand your networks. (Check news about PoE switch from FS.COM: Build and Expand Your Network with FS.COM New Introduced PoE Switches) So if you need to link multiple switches, you need to select switches with enough Gigabit ports.

Power Supplies for Powered Device

PoE switch applies two standards: IEEE802.3af and 802.3at. Each one can offer power for IP cameras. Due to the different standards, the output power of PoE switch is also different. IEEE802.3af can provide 15.4watts DC power on each port. As some power dissipates in the cable, only 12.95watts power at most can be supplied to powered devices. This standard is enough to power VoIP phones, wireless access points and some cameras over standard Ethernet cabling. While, IEEE802.3at is updated PoE standard known as PoE+. It can provide up to 25.5watts power available for powered device which is nearly twice as many as that 802.3af supplies. The updated standard can support more devices with high-power functionality such as door controllers, cameras with zoom capacity, or wireless access points supporting 802.11n.

Total Power

PoE switch has a total power. As described before, under IEEE802.3af standard, each port on the PoE switch can get 15.4watts power. Thus, the total power of a 24-port switch must reach 370watts so that it can make sure each port get sufficient power. And make sure there is additional power beyond that required for PoE for its switching functions. As to the IEE802.3at standard, each port supports 30watts. Under this condition, the PoE switch with total power of 370watts can only provide power supply to 12 ports.

Cable Requirements

The DC power of IEEE 802.3af standard is 15.4watts. It can support 10BASE-T and 100BASE-T. Two of four twisted pairs of Cat3 cable or higher can support the power and data transmission. The PoE+ standard delivers power up to 30watts and supports 1000BASE-T. Cat5e or Cat6 cable is able to support the power transmission. Connecting PoE switch to the router or cameras with Cat5e or Cat6 cable, the maximum transmission length is up to 100 meters.

When buying Ethernet cables, find a reliable vendor who provides standard network cable meeting the strict requirement. PoE power supply must use oxygen-free copper material—standard network cable. Non-standard cable utilizes other materials such as copper clad steel, copper clad aluminum, copper coated iron, etc. These cables are not suitable for PoE power supply because of the big resistance.

Conclusion

PoE switch is a cost-effective solution to increase the reliability and security of networks by providing centralized backup power to all connected IP surveillance devices. Before purchasing PoE switches, try to know as more details about the switch specifications as possible and also your own needs. To get good quality PoE switches, please come to FS.COM.

How to Choose a Wireless Access Point?

Nowadays, wireless LAN (local area network) becomes an independent part in our daily life. As waiting for your dishes in a restaurant, you may take out your phone and connect the Wi-Fi. I guess most of you have a wireless LAN. But if you have no or intend to upgrade your network, you’d better read this article on how to choose a wireless access point (AP).

fs-wifi-ap

Wireless AP Standards: 802.11n and 802.11ac

There are two newest IEEE wirelesss network standards including 802.11n (debuting in 2009) and 802.11ac (in 2014). The earlier 802.11n standard can support up to 540 Mbps, while the optimized 802.11ac products can provide the speed up to 1.3Gbps. 802.11ac is faster and more scalable than 802.11n. Except the improved speed, 802.11ac access points also optimize in the areas of range and reliability. Considering these factors, many enterprises may use 802.11ac technology.

However, though 802.11ac is better than 802.11n, it doesn’t mean it suits for everyone. First, 802.11ac needs big room for super wide channels. Second, you need to buy devices matching 802.11ac technology. At last, those devices should be close (20 or 30 feet) to the access point.

Dual Band Wireless AP or Single Band Wireless AP

Before discussing about dual band and single band, we need to know 2.4 GHz and 5 GHz. 2.4 GHz is a lower frequency than 5 GHz. It can penetrate most obstructions better. The signal can reach further. Wireless access point is one of the devices which use 2.4 GHz. While 5 GHz has a higher frequency, signals can’t penetrate solid obstructions like walls as easily as 2.4 GHz. 5 GHz provides us with more usable channels.

dual-band-wireless-ap

In the past, some 802.11n wireless AP is single band and can only support 2.4 GHz. It fails to meet the demands for 5GHz devices. Thus, the trend urges the appearance of new dual-band access point. Dual-band means that the access point can transmit and receive in two separate bands. Dual-band access points can support 2.4 GHz speeds and leverage wide channels, high data rates for connecting 5GHz devices. When you buy access points, make sure the one you choose can support both 2.4 GHz and 5 GHz.

Spatial Streams of Wireless AP

The number of spatial streams is one of the influencing factors on wireless speed. 802.11n stopped at four spatial streams, but 802.11ac goes all the way to eight. 802.11n introduced MIMO (more multiple input, multiple output). MIMO means that we can get multiple radio chains and antennas to transmit and receive. The more radio chains, the faster the wireless network speed. With 802.11n, a device can transmit multiple spatial streams at once, but only directed to a single address. It means only one user can get data at a time. That’s called single-user MIMO (SU-MIMO). While with 802.11ac, multi users can get data at the same time. And that’s called multiuser MIMO (MU-MIMO). As you can see, the more spatial streams, the better.

Get Wireless APs From Fiberstore

We provide three types of wireless APs which can be applied to enterprises, schools, hotels, etc. Our wireless APs contain the good features of easy plug & play installation and intuitive management, which is beneficial for reducing the need for dedicated IT personnel resources. And the unique watchdog technology makes AP work more stable and ensure the wireless network operate properly. Repeater mode makes wireless coverage more flexible. Both 802.11n and 802.11ac APs (as shown in the table below) can be found in Fiberstore.

Image 2.4GHz Speed 5.8GHz Speed CPU Antenna Gain
AP-S300 ap-s300 300 Mbps No 533 MHz 2x3dBi
AP-D1200 ap-d1200 300 Mbps 867 Mbps 650 MHz 4x3dBi
AP-D1750 ap-d1750 450 Mbps 1300 Mbps 720 MHz 6x3dBi
Conclusion

This article is to give you some advice on how to choose a wireless access point. Well, when you decide to buy one, remember the tips mentioned above including standards, dual band or single band, spatial streams. The most suitable is the best. A reliable vendor is also important. Hope this article can help you find your desirable wireless AP.

Fiber Splitter for FTTH Applications

Passive optical network (PON) has been widely applied in the construction of FTTH (fiber to the home). With PON architecture, network service providers can send the signal to multiple users through a single optical fiber, which can help them save great costs. To build the PON architecture, optical fiber splitter is necessary.

What Is Fiber Splitter?

The fiber splitter is a passive component specially designed for PON networks. Fiber splitter is generally a two-way passive equipment with one or two input ports and several output ports (from 2 to 64). Fiber splitter is used to split the optical signal into several outputs by a certain ratio. If the ratio of a splitter is 1×8 , then the signal will be divided into 8 fiber optic lights by equal ratio and each beam is 1/8 of the original source. The splitter can be designed for a specific wavelength, or works with wavelengths (from 1260 nm to 1620 nm) commonly used in optical transmission. Since fiber splitter is a passive device, it can provide high reliability for FTTH network. Based on the production principle, fiber splitters include Planar Lightwave Circuit (PLC) and Fused Bionic Taper (FBT).

PLC splitters are produced by planar technology. PLC splitters use silica optical waveguide technology to distribute optical signals from central office to multiple premise locations. The output ports of PLC splitters can be at most 64. This type of splitters is mainly used for network with more users.

The Structure of PLC splitters

Internal Structure

The following figure shows a PLC splitter. The optical fiber is splitted into 32 outputs. PLC chip is made of silica glass embedded with optical waveguide. The waveguide has three branches of optical channels. When the light guided through the channels, it is equally divided into multiple lights (up to 64) and transmitted via output ports.

1x32-plc-splitter

Outside Configuration

Bare splitter is the basic component of PLC fiber splitter. For better protection of the fragile fiber and optimized use, PLC splitters are often equipped with loose tube, connector and covering box. PLC splitters are made in several different configurations, including ABS, LGX box, Mini Plug-in type, Tray type, 1U Rack mount, etc. For example, 1RU rack mount PLC splitter (as shown in the figure below) is designed for high density fiber optical distribution networks. It can provide super optical performance and fast installation. This splitter is preassembled and fibers are terminated with SC connectors. It’s ready for immediate installation.

rack-mount-plc-spllitter

FBT splitters are made by connecting the optical fibers at high temperature and pressure. When the fiber coats are melted and connected, fiber cores get close to each other. Then two or more optical fibers are bound together and put on a fused taper fiber device. Fibers are drawn out according to the output ratio from one single fiber as the input. FBT splitters are mostly used for passive networks where the split configuration is smaller.

PLC Splitters From FS.COM

Fiberstore offers a wide range of PLC splitters that can be configured with 1xN and 2xN. Our splitters are designed for different applications, configurations including LGX, ABS box with pigtail, bare, blockless, rack mount package and so on.

Port Configuration Package Style Fiber Diameter
(Input/output)
Connector (Input/output) Pigtail Length
1×2 Steel tube, bare fiber 250μm None 1.5m
1×4 Mini module 900μm SC APC/UPC 2.0m
1×8 Pigtailed ABS box 2.00mm LC APC/UPC 3.0m
1×16 Mini plugged-in 3.0mm FC APC/UPC Customized
1×32 LGX ST APC/UPC
1×64 Splice Tray Type Customized
2×16 Rack mount
Conclusion

Fiber splitter is an economical solution for PON architecture deployment in FTTH network. It can offer high performance and reliability against the harsh environment conditions. Besides, the small sized splitter is easy for installation and flexible for future network reconfiguration. Therefore, it’s a wise choice to use fiber splitter for building FTTH network.

What Should You Know About Fibre Channel?

Before Fibre Channel appears, SCSI (small computer system interface) was used as the transmission interface between servers and clustered storage devices. But as the high speed demands keep increasing, Fibre Channel replaces SCSI inevitably due to its higher transmission data rate, flexibility, and long distance. This article is going to introduce you some details about Fibre Channel.

What Is Fibre Channel?

Fibre Channel, short for FC, is a technology for transmitting data between computer devices at data rate of 1, 2, 4, 8, 16, 128 Gbps. It’s mainly used in storage area networks (SAN) in commercial data centers. It’s useful for connecting computer servers to shared storage devices and for interconnecting storage controllers and drives.

Fibre Channel Transceivers

Except optical fiber cable, Fibre Channel transceiver is the other vital equipment to connect the Fibre Channel network in data centers. It provides the interface between Fibre Channel systems and the optical fibers of the SAN. FS.COM offers SFPs and SFP+s that are compatible with Fibre Channel. Fiberstore Fibre Channel SFPs support the distance up to 80km and the data rate of 2G/4G. As to our Fibre Channel SFP+ transceivers, they can support the data rate up to 8Gbps and 10Gbps. In Fiberstore, you can also find some compatible brands of FC transceivers including Cisco, Juniper, Brocade, HPE, etc. What’s more, all these modules have been tested to assure 100% compatible. For your information, the following table shows some hot FC transceivers for 2G/4G and 8G/10G network applications.

Model Description
37656 2G Fibre Channel SFP 1310nm 10km DOM Transceiver
15376 Cisco DS-SFP-FC8G-ER Compatible 8G Fibre Channel SFP+ 1550nm 40km DOM Transceiver
15231 Cisco DS-SFP-FC8G-SW Compatible 8G Fibre Channel SFP+ 850nm 150m DOM Transceiver
33293 HPE (ex QLogic) AJ718A Compatible 8G Fibre Channel SFP+ 850nm 150m DOM Transceiver
39630 HPE (ex Brocade) AJ716B Compatible 8G Fibre Channel SFP+ 850nm 150m DOM Transceiver
35932 Brocade XBR-000163 Compatible 8G Fibre Channel SFP+ 850nm 150m DOM Transceiver
fibre-channel-sfp-sfp-plus
Transfer to High Speed Fibre Channel

However, as the need for high-bandwidth never stops increasing, the data rate of 2G, 4G or even 8G can’t meet the high speed requirements. So many data centers move to higher Fibre Channel standards, for example, 16G Fibre Channel. 16G FC links increase the network speed twice as 8G FC and 40% faster than 10G FC. The transition to 16G FC makes data transfer smoother, quicker and cost-effective from the good side. But from the other side, the transition still faces some challenges. There might be some data communication error rates that may affect the network performance. And the physics of 16G FC can possibly bring some new restrictions on fiber cabling and transceiver modules. Therefore, before starting to transfer to higher speed Fibre Channel infrastructure, you should better follow the tips listed below.

First, cleaning issue. In fiber optics connection, contamination is thought as a big problem which may lead to link failure. So you should clean all the transceiver modules, connectors and other cable junctions to ensure there is no contamination in the fiber optic connection. Some fiber testers and cleaning tools are necessary for your cleaning work.

Second, analyze the optical power budget between transmit and receiver ports. It requires that the power margin (transmit power minus power loss during the data transmission through the cable) should be more than the receiver power of the optical transceivers. At the same time, it also should meet the FC protocol specification.

Third, measure the light level on the transmitting side and receiving side. You can use suitable fiber optical light source or optical power meter to measure the power level on critical links. If the power level were not in the right station, check whether the cable length is suitable or cable bend radius reaches the maximum. Then you are suggested to purchase customized bend insensitive fiber cable for your special use.

Summary

Fibre Channel is commonly used for the connection of SAN in enterprise storage. You can find 2G/4G FC SFPs, 8G/10G FC SFP+ modules and matching fiber patch cables from FS.COM. If you need to upgrade your Fibre Channel network to 16G or even higher, remember the above tips and make sure the 16G FC are compatible with 4G FC and 8G FC.

Related article: Netgear AGM731F Compatible SFP for Gigabit Ethernet and Fibre Channel Applications

Transceiver Solutions for Ubiquiti UniFi Switches

UniFi switch is one type of the switches Ubiquiti has introduced into the market (The other kind is Ubiquiti EdgeSwitch). The UniFi switch provides fiber connectivity options for easy expansion of your networks. This article will introduce the main features of UniFi switches, supportable SFP and SFP+, and easy tips for building network with UniFi switch.

Introduction to UniFi Switches

UniFi switch delivers high performance to satisfy your growing network. The Ubiquiti UniFi switches include US-24 and US-48. US-24 can support data rates up to 26 Gbps while US-48 can support the network speed up to 70 Gbps of non-blocking throughput. Main features of these two switches are described as below.

unifi-switch-ports

Features of US-24 switch:

  • 24 Gigabit RJ45 ports
  • 2 SFP ports
  • 52Gbps switching capacity
  • 250W max. power consumption
  • Rack mountable

Features of US-48 switch:

  • 48 Gigabit RJ45 ports
  • 2 SFP+ ports
  • 2 SFP ports
  • 140Gbps switching capacity
  • 56W max. power consumption
  • Rack mountable

Except the above two switches, there are some other kinds containing US-8-150 (with 8 Gigabit RJ45 ports and 2 SFP ports) and US-16-150W (with 16 Gigabit RJ45 ports and 2 SFP ports). Both switches are available with different models. You can find the details about these models from the following table.

unifi-switch-comparison

Compatible SFP and SFP+ for UniFi Switch

If you are wondering which SFP and SFP+ are suitable for UniFi switch, you can get the answer now. You have two choices for getting suitable transceiver modules. Ubiquiti produces single-mode and multimode SFP and SFP+ modules for UniFi switches. UF-MM-1G and UF-MM-1G-S are designed for SFP ports. Three modules such as UF-SM-10G, UF-SM-10G-S, and UF-MM-10G are appropriate for SFP+ ports.

Of course, transceiver modules for UniFi switch are not limited to these original SFP/SFP+. A wide range of third-party transceivers can also work with UniFi switch. The following table will show you some compatible SFPs for Unifi switch from FS.COM.

Fiberstore compatible SFPs for Unifi switch

ID # Description
20363 Cisco GLC-SX-MM-RGD Compatible 1000BASE-SX SFP 850nm 550m DOM Transceiver
11774 Cisco GLC-SX-MM-RGD Compatible 1000BASE-SX SFP 850nm 550m DOM Transceiver
32140 HPE J4858C Compatible 1000BASE-SX SFP 850nm 550m DOM Transceiver

Fiberstore compatible SFP+s for Unifi switch

ID # Description
48895 1m Brocade 10G-SFPP-TWX-0101 Compatible 10G SFP+ Active Direct Attach Cable
36671 1m Brocade 10G-SFPP-TWX-0101 Compatible 10G SFP+ Passive Direct Attach Cable
30849 1m Cisco SFP-H10GB-CU1M Compatible 10G SFP+ Passive Direct Attach Copper Twinax Copper Cable
48884 1m Cisco SFP-H10GB-ACU1M Compatible 10G SFP+ Active Direct Attach Copper Cable
Building Connection With Unifi Switch

To build the UniFi network, you have to prepare installation screwdriver, at least 1U rack, UTP Cat 5 (or above) for indoor applications and STP Cat5 (or above) for outdoor applications. It’s quite easy.

  • First, install the UniFi switch on the rack with four mounting screws. Then plug one end of the power cord into the power port of the UniFi switch and the other end into the power outlet.
  • Second, connect Ethernet cables from your devices to RJ45 ports of UniFi switch.
  • Third, plug an SFP transceiver into the SFP port if you need to use it. After that, connect the SFP module with a fiber patch cable.
Conclusion

UniFi switches are very commonly used for network connection. To build the network, you don’t need to spend much time on searching cables or modules from the internet. FS.COM offers fiber patch cables and Ethernet cables for your connection. We also provide some compativle SFPs and SFP+s definitely compatible for UniFi switch. Every module has been strictly tested to make sure high quality. Just come to our site and you must get 100% compatible SFP or SFP+s for your UniFi switch.

Related FS.COM News: FS.COM Offered 100% Compatible Optics for Ubiquiti Platform

Economically Increase Network Capacity With CWDM Mux/DeMux

As the demands for voice, video and data networks are increasing dramatically, more bandwidth and higher transmission speed over long distances are needed. To meet these demands, it means that service providers should depend on more fiber optics which definitely cause more costs for optical devices. But they apply Wavelength Division Multiplexing (WDM) technologies which is a cost-effective way to increase capacity on the existing fiber infrastructure.

CWDM Technology

WDM technology multiplexes multiple optical signals onto a single fiber by suing different wavelengths, or colors, of light. WDM can expand the network capacity using existing fiber infrastructure in an economical way. It includes CWDM (Coarse Wavelength Division Multiplexing) and DWDM (Dense Wavelength Division Multiplexing).

CWDM is a technology multiplexing 16 channels onto one single fiber between the wavelengths from 1270 nm to 1610 nm. It’s designed for city and access network. Since the channel spacing is 20 nm, CWDM is a more cost-effective method to maximize existing fiber by decreasing the channel spacing between wavelengths. CWDM is a passive technology, therefore, CWDM equipment needs no electrical power.

cwdm-channel

Figure 1

CWDM technology has been applied into wide areas, such as CWDM optical transceivers, CWDM OADM and CWDM Mux/DeMux. CWDM Mux/DeMux modules are multiplexers and demultiplexers which provide long distance coverage with premium optical technology to enhance fiber optic systems. It multiplexes signals of different wavelengths on one single fiber and demultiplexes wavelengths to individual fibers. CWDM Mux/DeMux can offer low-cost bandwidth and upgrade the existing system without leading spare costs on more fibers. CWDM Mux/DeMux can hold up to 18 channels of different standards (for example, Fibre Channel, Gigabit Ethernet) and data rates over one fiber optic link without interruption. FS.COM offers a full series of CWDM Mux/DeMux, including 2, 4, 8, 9, 12, 16, 18 channels with or without monitor port and expansion port in 1RU 19” rack chassis or pigtailed ABS module. The following will show you how to use a 18-channel CWDM Mux/DeMux to increase the data rates up to 180 Gbps on a fiber pair.

In Figure2, all Cisco compatible 10G CWDM SFP+ 1270-1610 nm 40km DOM transceivers on the switch are connected with the CWDM Mux/DeMux by LC-LC fiber patch cords. This CWDM Mux/DeMux has 18 channels and is designed as 1 RU rack mount size, covering the wavelengths from 1270 nm to 1610 nm and supporting LC UPC port. During the long distance transmission, only one single-mode armored LC fiber patch cord is needed to achieve 180 Gbps by connecting the two 18-channel CWDM Mux/DeMux. Thus, it greatly saves the cost for increasing the bandwidth on the existing fiber infrastructure.

cwdm-mux-18ch

Figure 2

FMU CWDM Mux/Demux

To increase the capacity, it requires more space and cable management is also a big trouble. So Fiberstore independently researched and developed FMU CWDM Mux/DeMux to solve this problem. We provide FMU 16-ch 1U Rack CWDM MUX/DEMUX specially designed as 2-slot plug and play style, which allows you to add or remove fiber fiber optic cables and plug-in-modules freely according to your applications. There are two separate CWDM plug-in modules. One is high band (1470nm-1610nm) module with an expansion port and the other is low band (1270nm-1450nm, skip 1390nm, 1410nm) module without expansion port. Via this expansion port, channels can be expanded over one pair of fiber without interruption. You can also insert two CWDM Mux/DeMux FMU-plug-in modules without expansion port for two separated 8-channel connections. Besides, you can mix CWDM and DWDM system by adding CWDM Mux/DeMux FMU-plug-in modules and DWDM Mux/DeMux FMU-plug-in modules with matching wavelengths.

2-slot-cwdm-mux2

Figure 3

FS.COM FMU Plug-in Modules

The table below lists both single fiber and dual fiber FMU plu-in modules for 2-slot CWDM Mux/DeMux. You can choose suitable modules according to you specific requirements. Custom service is available, too.

ID# Description
30431 2, 4, 5, 8, 9 Channels, CWDM Mux Demux, Single Fiber, Type A, Plug-in Module
30447 2, 4, 5, 8, 9 channels, CWDM Mux Demux, Single fiber, type B, Plug-and-play module
43553 4 Channels 1490-1610nm Single Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
43554 4 Channels 1470-1590nm Single Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
48393 4 Channels 1470-1590nm Single Fiber CWDM Mux Demux with Expansion Port, FMU Plug-in Module, LC/UPC
48394 4 Channels 1490-1610nm Single Fiber CWDM Mux Demux with Expansion Port, FMU Plug-in Module, LC/UPC
43779 8 Channels 1310-1610nm Single Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
43780 8 Channels 1290-1590nm Single Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
43699 9 Channels 1290-1610nm Single Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
43711 9 Channels 1270-1590nm Single Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
30414 2, 4, 5, 8, 9 Channels, CWDM Mux Demux, Dual Fiber, Plug-in Module
42944 4 Channels 1510-1570nm Dual Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
42972 4 Channels 1270-1330nm Dual Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
42973 4 Channels 1510-1570nm Dual Fiber CWDM Mux Demux with Expansion Port, FMU Plug-in Module, LC/UPC
42945 8 Channels 1290-1430nm Dual Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
43097 8 Channels 1470-1610nm Dual Fiber CWDM Mux Demux, FMU Plug-in Module, LC/UPC
43099 8 Channels 1470-1610nm Dual Fiber CWDM Mux Demux with Expansion Port, FMU Plug-in Module, LC/UPC
Conclusion

If you would like to increase your network bandwidth while spend less money on changing existing infrastructure, CWDM Mux/DeMux is an economical solution. FS.COM brings you high quality CWDM Mux/DeMux module and newly self-developed FMU 2-slot CWDM Mux/DeMux modules & FMU plug-in modules. For detailed information, please visit our site www.fs.com or contact us through sales@fs.com.

Check out All CWDM Transceiver Modules

Coarse Wavelength Division Multiplexing (CWDM) is one of WDM technologies. It uses up to 20 different wavelengths for data transmission over a single fiber. CWDM applies coarse wavelength grid and it allows low-cost, uncooled lasers, which makes CWDM systems less expensive and consuming less power. There are many optical equipment applying CWDM technology. This article will introduce CWDM optical transceivers.

fs-cwdm-sfp

CWDM Transceivers

CWDM transceiver is a kind of optical modules employing CWDM technology. CWDM transceivers enable connectivity between existing network equipment and CWDM Multiplexers/DeMultiplexers (Mux/DeMux). When used with CWDM Mux/DeMux, CWDM transceivers can increase network capacity by transmitting multiple data channels with separate optical wavelengths (1270 nm to 1610 nm) over the same single fiber. CWDM transceivers are also useful for reducing network equipment inventories by eliminating the need to maintain surplus units/ devices of various fiber types for network repairs or upgrades. CWDM transceivers include four types, such as CWDM SFP, CWDM SFP+, CWDM XFP and CWDM X2. The following shows more details about these CWDM transceiver modules.

CWDM Transceiver Module Types

CWDM SFPs are hot-pluggable transceiver modules. CWDM SFP transceivers are SFP MSA (Multi Sourcing Agreement) and IEEE 802.3 & ROHS compliant. CWDM SFPs can provide data rates including 1G, 2G and 4G over the link distance of up to 200 km by connecting with duplex LC single-mode patch cords. CWDM SFPs transmit multiple data channels by combining separate optical wavelengths onto a single fiber to increase network capacity. CWDM SFPs can be used to support the CWDM passive optical system combing CWDM OADM (optical add/drop multiplexer). When CWDM SFPs used with transponders and media converters, these two optical components offer convenient method to convert existing legacy equipment with standard wavelengths or copper ports to CWDM wavelengths.

CWDM SFP+ offers service providers and enterprise companies an easy way to get a scalable 10 Gigabit Ethernet network. It is a cost-effective solution for 10 Gigabit Ethernet applications in campus, data center and metropolitan area access networks. CWDM SFP+ can transport up to eight channels of 10 Gigabit Ethernet over single-mode fiber strands at the wavelengths including 1610 nm, 1590 nm, 1570 nm, 1550 nm, 1530 nm, 1510 nm, 1490 nm, and 1470 nm. CWDM SFP+ solution is helpful to increase the bandwidth of an existing 10 Gigabit Ethernet optical infrastructure without adding new fiber strands. The solution can be used in parallel with other SFP+ devices on the same platform.

CWDM XFP is a hot-pluggable module designed in Z-direction and mainly used for typical routers and switch line card applications. CWDM XFP transceivers are designed for Storage, IP network and LAN. They comply with CWDM XFP MSA. CWDM XFPs cover the wavelengths from 1270 nm to 1610 nm. These modules can support the distance up to 100 km, which depends on the wavelengths, fiber types and the CWDM Mux/DeMux insertion loss.

CWDM X2 transceiver is designed for CWDM optical data communications such as 10G Ethernet and 10G Fibre Channel applications. CWDM X2 wavelengths are available from 1270 nm to 1610 nm. CWDM X2 is MSA Compliant. It supports the transmission distance up to 80 km connecting with duplex SC single-mode fiber cable.

Conclusion

CWDM technology provides a low-cost solution which allows scalable and easy-to-deploy Gigabit Ethernet and Fibre Channel services. CWDM transceivers enable a more flexible and highly available multi-service network with the combinations of CWDM OADMs and CWDM Mux/DeMux. FS.COM offers all kinds of CWDM transceivers like CWDM SFP, CWDM SFP+, CWDM XFP, CWDM X2. Our CWDM transceivers are compatible with most famous brands and all these optics have been fully tested to make sure high compatibility. For more details about Fiberstore CWDM transceivers and other CWDM equipment, please visit our site www.fs.com or contact us via sales@fs.com.

Fiber Optic Components for Building 10G Data Centers

10 Gigabit Ethernet is a telecommunication technology that can support the network speed up to 10 billion bits per second. It’s also known as 10GbE. As 10GbE greatly increases bandwidth, many companies start to upgrade the data centers to meet their growing needs. How to build a 10G data center? What kind of equipment will be used except the switch? This article will recommend you some basic 10G solutions.

10G SFP+ (small form-factor pluggable plus) modules are hot swappable transceivers that plug into SFP+ slots on switches and support 10G data center. With small form factor, SFP+ transceivers can ensure low power disruption and high port density. Since it’s hot pluggable, the transceiver modules can be added or removed without interrupting the whole network. And SFP+ modules deliver data transmission speed of up to 10Gbit/s, which is 10 times faster than Gigabit Ethernet.

10g-sfp-module

Currently, a wide variety of SFP+ modules can be purchased in the market. For the long distance transmission, modules include SFP-10GBASE-LR, SFP-10GBASE-ER, SFP-10GBASE-ZR, CWDM SFP+ and DWDM SFP+. For the short distance transmission, there are modules like SFP 10GBASE-SR, SFP-10GBASE-LRM. Brands are also versatile such as Cisco, Juniper, Arista, Brocade, etc. To get modules with lower costs, you can pick third-party transceivers which are compatible with these original brands.

Patch cables contain both fiber and copper types. Fiber patch cords, as one of the data transmission media, enjoy great popularity because they have large transmission capacity, strong anti-electromagnetic interference, high security and fast speed. LC fiber patch cord is one of the most common cables for 10G data center, covering single-mode and multimode categories respectively for data transmission over long distance and short distance. To increase panel density, flexible HD LC push-pull tab fiber patch cable is designed. With its unique design, this patch cable allows the connector to be disengaged easily from densely loaded panels without the need for special tools and give users easy accessibility in narrow areas for data center deployment applications. Another special LC patch cord is uniboot patch cord. It utilizes a special “round duplex” cable that allows duplex transmission within a single cable. It’s good for saving cable management space comparing to standard patch cords.

lc-patch-cable

10G SFP+ Direct Attach Cable Assemblies

10G SFP+ direct attach cable (DAC ) is a cost-effective solution for 10G data center. It’s a low-power alternative to optical SFP+ system. The 10G SFP+ cables provide low-cost and reliable 10G speed with either copper cables over distances up to 10 m or active optical cables reaching distances up to 100 m. Because there is no need for spending on fiber optic transceivers and cables. This kind of cables contain 10G SFP+ copper cables, both passive and active and active optical cable (AOC). Active copper cable and AOC are designed for long distance connection, while passive copper cable is for short distance, such as the interconnection of top-of-rack switches with application servers and storage devices in a rack.

10g-sfp-cables

Fiber Enclosure

Fiber enclosure is an equipment you must have in data centers. This component is used to provide a flexible and modular system for managing fiber terminations, connections, and patching in high density data center application to maximize rack space utilization and minimize floor space. Fiber enclosure can be divided into different configurations like rack mount (available in 1U, 2U, 3U, 4U), wall mount, indoor or outdoor. The rack mount enclosure come into three flavors. One is the slide-out type and the other two are removable type and swing out type. Fiberstore introduces high density fiber enclosures with 48 ports, 96 ports and even 288 ports loaded LC FAPs (fiber adapter panels) in 1RU or 4RU rack mount for 10G solutions. Or if you already have the unloaded fiber enclosures, you just need to buy fiber adapter panels.

288-pors-4u-patch-panel-enclosure

Conclusion

To build a 10G data center, you have to prepare the components, for instance, 10G SFP+ modules, LC patch cables, 10G SFP+ cables, fiber enclosures, etc. You may also need other instruments for testing and cable organization. And all those equipment can be got from FS.COM with higher quality but fewer costs. For more information, you can contact us via sales@fs.com.